When printing color printed materials, there are many factors that can affect the quality of the printed materials, resulting in many printed materials being not well produced. Among them, overprinting is one of the main factors that affect the quality of the printed materials. However, many factors in the printing process can affect overprinting. So, during the printing process, attention should be paid to these two major points that appear on the paper and printing plate:

一、紙張外表越粗糙，油墨的吸收量就越大。打印紙的粗糙外表，油墨泛濫現象更容易出現。這是因?yàn)橛行┘垙埨w維的交織發生的間隙，均勻的涂層還沒有很好的覆蓋。這種壓紋紙和印版時，油墨層外表發生不良接觸。如果通過適當?shù)挠∷毫?，可以有足夠的接觸時間與油墨層的布局的紙張的平滑性差，實現均勻的壓印接觸，可以確保印刷墨層均勻平服。

1、 The rougher the surface of the paper, the greater the absorption of ink. The rough surface of printing paper is more prone to ink flooding. This is because some paper fibers have interwoven gaps, and the uniform coating has not yet covered them well. When this type of embossed paper and printing plate, there is poor contact on the surface of the ink layer. If appropriate printing pressure is applied, there can be sufficient contact time with the layout of the ink layer, resulting in poor smoothness of the paper, achieving uniform embossing contact and ensuring a uniform and flat printing ink layer.

二、保守膠合板面前底部支架的印刷版，不只有許多弊端，容易呈現油墨轉移不良現象，引起油墨布局不均的發生。這是因?yàn)槟静牡牡撞客斜P(pán)不夠強，變形的可能性也比較大，導致不穩定的印刷壓力，油墨層的布局不能均勻地轉印到紙張上。更好的方法就是做好備份操作技術，一些印刷板面積較大，應選擇一些平整度好，比擬扎實的金屬版本的護理，可以更好的防止這些現象的發生。

2、 The printing plate of the bottom bracket in front of the conservative plywood has many drawbacks, which can easily lead to poor ink transfer and uneven ink layout. This is because the bottom tray of the wood is not strong enough, and the possibility of deformation is also high, resulting in unstable printing pressure and the layout of the ink layer cannot be evenly transferred onto the paper. The best method is to do a good job in backup operation technology. Some printed boards have a large area, and should choose metal versions with good flatness and solidity for care, which can better prevent these phenomena from happening.

彩色印刷品在設計和疊印的處理上要注意以下六點：

The following six points should be noted in the design and overprint processing of color printed materials:

1、字形過小的文字應避免選擇筆畫太細的字體，比如仿宋體、細圓體等，字體的筆畫原本就細，如果字形過小，印刷時筆畫就容易丟失，導致字跡不全；

1. For text with a small font size, it is recommended to avoid choosing fonts with too thin strokes, such as imitation Song typeface, thin circle, etc. The strokes of the font are already thin. If the font size is too small, the strokes may be lost during printing, resulting in incomplete handwriting;

2、尤其是細小的文字，應避免使用多色套?。?/div>